Our top pick
HeatTrak walkway mat HR20-60
The HR20-60 is a rubber walkway mat with a heating element sealed between two non-slip surfaces. You lay it on a step landing, a path or a deck, plug it in, and it warms from below.
HeatTrak states it can melt 2 in of snowfall an hour at most, keeping the surface about 40 °F warmer than the air. The listing says it works well down to -8 °F and is made to stay outside all season.
Its 2.5 A draw at 120 V comes to roughly 300 W, by our arithmetic. That modest draw is why one Power Unit can feed this mat plus several stair treads.
- Size
- 20 × 60 in, about 0.5 in thick
- Power draw
- 2.5 A, about 300 W
- Melt rate
- Up to 2 in of snow per hour
- Surface
- About 40 °F above the air
- Cold limit
- Works well to -8 °F (listing)
- Power
- Power Unit needed, sold separately
- Weight
- 8.28 lb
- Warranty
- 2 years from shipment
From the box to the first storm, step by step
Most disappointments with this mat come from the setup, not the mat. This is the order HeatTrak’s FAQ and listings point to.
Before the first snow
- Find your outdoor outlet and confirm it is GFCI protected, with an in-use cover
- Order a Power Unit with the mat, or buy the HR20-60P with one included
- Lay the mat flat on the path, cord side away from where people walk
- Mat into Power Unit, Power Unit into the outlet, every connection kept out of water
- Add up the amps on the chain and stay under 13 A
Then leave it out for the winter
Every snowy day
- Switch it on before the snow starts, not once it has piled up
- Let the heat do the work, with no shovel, ice chipper or snow blower on the mat
- Check that no cord sits in a puddle or under a closing door
- At winter’s end, let it cool, check the cords and store it flat and dry
What it has, and what it lacks
What it has
- Up to 2 in of snow melted per hour
- Chaining to HeatTrak stair treads and walkway mats
- A low 2.5 A draw that leaves room on the circuit
- A build meant to stay outside all season
- Two-year warranty from the date of shipment
What it lacks
- A Power Unit in the box, so it cannot run alone
- A thermostat, so it is simply on or off
- Any way to trim it, since a mat must never be cut
- A low price once the Power Unit is added
Between us, before you order
This listing is the mat alone. Plug it into a wall and nothing happens, because it is built to run through HeatTrak’s Power Unit, the box with the GFCI in it. That surprise is the most common owner complaint.
If you own no Power Unit yet, the HR20-60P with the unit included is the simpler order. Buy this plain mat to extend a chain you already have.
HeatTrak’s FAQ caps one Power Unit at 13 A, while some listings say 14. Plan with 13, and put anything beyond it on a second unit and a second circuit.
What owners report
Owners say it keeps porches and steps clear, warms up fast and holds up well.
The top complaint is the missing Power Unit, and opinions on value are mixed once both parts are paid for. Some report failures after about five years, close to HeatTrak’s own average of 5–6 years. Our care guide covers the habits that stretch it.
Buy it if
You want a well-documented mat for a path or landing that can grow into a chain over the steps, and you already own a Power Unit or will buy one.
Skip it if
- No Power Unit yet? Take the HR20-60P starter mat
- Only steps to clear? Look at the HeatTrak stair tread
- Just the front door? Try the plug-in entrance mat
- Want one plug, one mat? See the Toriexon 20 × 60
Ready to stop shoveling the path?
Check the outlet, order the Power Unit alongside it, and switch it on before the first flakes. Do that, and the HR20-60 is the mat we would trust on our own front path.